Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
Hi to all,
I just purchase a proxmark3 which should be arriving in a week time.
The board is said to be flashed with firmware version svn-r486.
I intend to power up the proxmark 3 with an portable battery, Does anyone know what is the input power supply?
And if i place a LF tag infront of it, will it grab the LF signal or is there any step i need to do?
(Purpose : I want to copy the card LF into the proxmark3 and use the proxmark3 to access the LF reader.)
Best regards
Ng Raymond
Offline
Oops,
Think i saw the post for the battery in the General (USB driver, Framework, Protocol) section......
This look like the battery for the job,
Energizer XP2000
Specifications
Battery Cell: Lithium Polymer
Power Capacity: 2000 mAh
Rated Input: DC 5V, Max 500 mA
Rated Output: DC 5V, Max 500 mA
Recharge Time: ~4 Hrs
Weight: 0.16 lbs / 0.07 kg
Dimensions: 3.34(L) x 2.28(W) x 0.51(H) inches
So now is, if i connect the battery to the proxmark3.... will it power up and JUST work... or is that a step two or three....
Anyone who had done step two or three may be four,five can advise me... please....
Offline
Welcome to the forum!
The PM3 is usually powered via the mini USB plug. So, you can use your laptop or a standalone battery backup (w/mini USB plug) as the power source. As far as being able to read LF tags, it is very simple but, you will have to do a bit of reading. I think it is covered very nicely in the PM3 Manual on wiki.
Another note, there will be no spoon feeding here. Feel free to ask as many specific, to-the-point questions as you like.
Offline
Thanks for the Welcome Bugman1400,
Roger & Noted with thanks.
Hope i'am up to it.
Two more day's to go.
Offline
It here,now to test it.
I had connected a 5v battery pack to it.....
Connected the LF antenna.....
Step 1 - To get into stand-alone mode (works with or without a PC), hold the button for a second. You’ll see the lights go into a synchronized little bit. When done, the red1 LED will be lit. (Done)
Step 2 - When just red1 (next to the other two LEDs) is lit, that means slot 1 (red1) is selected. (Done , looking good)
Step 3 - When red2 is lit (and either red1/orange), that means the pm3 is recording and waiting for an HID tag to be detected. Once detected, the red2 light will turn off and the tag will be stored in the selected slot. (Okie,i've place a 1.25Hz Id card at the antenna, Done)
Step 4 - When green is lit (and either red1/orange), that means that specific slot is simulating the HID tag stored on that slot. ........... Its not working......
I placed the proxmark3 beside the card reader but nothing happen......
Question - How will i know if the proxmark3 had recorded the 1.25Hz id card?
Anyone can help?
Offline
It sounds like you need to do a bit of reading. I'd start with the PM3 manual on Wiki.
There is no 1.25kHz card. Do you mean 125kHz?
Forget the battery. Power the PM3 from a computer. The LED flashing, as you describe, looks correct. I have used this same feature a 100 times and it always works. You may need to practice first with the help of a computer (desktop or laptop) to get the hang of it.
Offline
Prm3 by raymond2017, on Flickr
Sorry about that, Is Low Frequency 125 kHz 26 bit HID Tag.
Ok - after a few time of testing....
1) Press one time - Running light.
2) Press second time - Red light.
3) Press and hold untill Two red light appear (About 2 second).
4) Place the HID card on the LF antenna, one red light will disppear (Meaning,the tag is store in proxmark3).
5) Red & green appear (Meaning that the slot is simulating the HID tag stored).
Think i had got it
Thanks Bugman1400.
Now to try the em card.
From internet - (RFID EM Proximity PVC Card with 125 KHz Operating Frequency)
1) Press one time - Running light.
2) Press second time - Red light.
3) Press and hold untill Two red light appear (About 2 second).
4) Place the HID card on the LF antenna..... waiting waiting........ Two red light is still there....
Arh......
Now changing to HF antenna ..............
Arh...... still the same.....
Ok, half time....... -_-
Offline
1)Cloning/replaying a HID Prox tag
From this post, you can see how you can use the HID-related commands to read & replay HID Prox tags.
Ok, so HID tag can be read & replay by using the card only......
2)Get the UID of a Mifare card using ’snooping’ capabilities¶Place a Mifare card on a Mifare reader (in this case, an Omnikey 5321), and put the antenna between the Mifare card and the reader.
Mifare card cannot be read by using the card only, will need the card and the reader........
3)
Manufacturer Tag name Frequency Modulation Read Simulate Snoop Comment
ST Micro SRI512 13.56MHz ISO14443-B Yes No Yes UID read, memory dump.
NXP and many others Mifare 13.56MHz ISO14443-A Yes Yes Yes Very Limited simulation capabilities in current firmware
NXP icode SLI 13.56MHz ISO15693 Yes No No Simulation code not working. Limited reading capabilities.
EM Microelectronics EM Marin
4200 series 125kHz 125kHz OOK Yes Yes No Simulation not tested, manchester encoded.
Exists in several variants, but I only encountered the Manchester type.
Nedap Nedap 125kHz 120kHz OOK Yes Yes No Simulation not tested, manchested encoded, works at 125kHz
HID (formerly Motorola) Indala 125kHz 125kHz BPSK Yes Yes No UID is scrambled, but replay works.
HID HID Prox 125kHz 125kHz FSK Yes Yes No Replay works. Decoding either on the Proxmark, or in the client.
So.... EM card Mifare card cannot be read by using the card only, will need the card and the reader........?
Now using the cpu to connect to the proxmark3, using the proxmark3 application.
Identifying an unknown tag
This method was documented in this proxmark.org forum post.
A really quick and easy way of determining if a card is HF or LF is to : 1. Run the tune command a couple of times to get an idea of what your voltage readings are on LF and HF. 2. place the unknown card/tag against the proxmark antennas (LF & HF) 3. Run the tune command a couple of times again to get an idea of what the values are wth the tag in the antenna fields 4. Look for significant voltage drops in either HF or LF, the voltage drop indicates the tag operating frequency. Generally you will see a voltage drop (sometimes over 10 volts) on the corresponding frequency (e.g. LF 125kHz/134kHz, HF 13.56MHz)
..............
Time to read more..........
Offline
Ran into a wall...........
I try to use cmd.exe and the exe in win32.....
proxmark3 exe by raymond2017
But got this error.
Proxmak3 Not found by raymond2017
Trying to Issue the „tune‟ command & „hidfskdemod‟.....
Am i doing the right thing?
Offline
My proxmark3 is plug in to my computer with the usb cable supply by proxmark.
Offline
That looks like Windows 7. If it is, have you loaded the correct signed drivers?
Offline
Yes,windows 7
Had try both the ways in this forum,but still not able to solve it.
http://proxmark.org/forum/viewtopic.php?id=531
Have you loaded the correct signed drivers?
I loaded the one in the folder win32 that was send to me.
It was missing a libusb0.dll, so i copy the dll from the proxmark driver.
After that i try adding the libusb0_x64.dll ,libusb0_x64.sys in both the folder (win32 & promark driver).
But still the same.
Proxmak3 Not found by raymond2017, on Flickr
Offline
Yes Bugman1440, its my drivers problem.
Many thanks too jason for the help.
Now reading around to solve the problem for my antenna check.
Offline
What is the problem with your antennae, it looks fine to me?
Your first 'hw tune' command looks great!
Your second and third 'hw tune' command looks terrible for a HF tag.
It looks like the 'if hid fskdemod' command did you in and resulted in unrecoverable errors but, it looks like you typed 'if' instead of 'lf'.
You may be better off on Windows XP until you figure the PM3 out.
Offline
Got the 'lf hid fskdemo' working already.
Many thank to Jason & Bugman1400
Now trying out the 'lf hid sim' command.
I had try to use a hid reader to read the data emulating from promark3 for id 0 as the img attached.
The emulating data is coming out from the Lf antenna right? Cos i place the reader at the antenna but was not able to get any reading.
But when, i place the tag for id 0 (32 bit) on the hid reader itself. The hid reader was able to detect it.
Offline