Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
@Marshmellow
Thanks. I have make all again. Is this correct now @Marshmellow? FPGA version is the latest one?
proxmark3> hw version
Prox/RFID mark3 RFID instrument
bootrom: /-suspect 2015-07-08 11:17:08
os: /-suspect 2015-07-08 11:17:11
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/06/22 at 21:47:54
uC: AT91SAM7S512 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 512K bytes. Used: 160828 bytes (31%). Free: 363460 bytes (69%).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory
Offline
That looks better
Offline
Added the new rev 2.2.0 to the 1st post !
Note that OS Image will be not be present anymore from now on ! Use fullimage to flash the firmware !
Offline
Added the new rev 2.3.0 to the 1st post.
It now supports HF sniff; settings.xml is not updated, if someome want to do that I will add them to the release package.
Last edited by asper (2015-11-05 00:11:42)
Offline
Added the new rev 2.4.0 to the 1st post.
It now supports piwi's topaz support ! Settings.xml is updated just for it, not for HF sniff.
Offline
hi,
i'm having an issue updating PM3 firmware here.
the latest version i can use is 2.1.0
ever since 2.2.0, my PM3 cannot read mifare card:
could someone please provide some advice here?
ps: from 2.2.0 i can only flash FLASH - Bootrom.bat and FLASH - fullimage.bat, not FLASH - OS.bat, is that the problem?
Thanks
Offline
@JasZ, this topic is not the place for problems. please post in the mifare section if that is the only issue you are experiencing.
ps. the osimage.elf has been done away with and it is included as part of the fullimage.elf
Offline
Added the new rev 2.5.0 to the 1st post.
Offline
Some how the new flash screwed out the "electhouse offline proxmark3 v3 version", is there a work around ?!
Offline
try flash it again, sometimes you'll need to keep the button pressed...
Offline
I tried to compile windows client under Windows 10 64 Bit but got these errors :
Any ideas on how to fix it?
Offline
Perl seems to be annoyed, running in mingw32 on a window10 64bit. Luckily for you, the mkversion.pl is not essential for the compilation process.
Offline
So, it is not possible to compile under win 10 64 bit, correct?
Offline
Since you had trouble, I had to test it myself.
I downloaded 2.2.0 and ProxSpace-130613.
Unpack the ProxSpace-130613
Inside I renamed pm3 -> pm3old
unpacked the 2.2.0
and renamed it to pm3
double clicked the runme.bat,
make clean && make all
and it compiles all fine, om my win10 64b,,...
Offline
It might be permission issues. Make sure the process owner has full rights.
Offline
Dear Iceman,
When you say you downloaded 2.2.0, where can I download this file?
I only download Proxspace and then sync it with github as per instruction on https://github.com/Proxmark/proxmark3/wiki/Windows.
What should be the size of compiled proxmark.exe?
Thanks.
Offline
BTW I've been running win 10 64 bit for months with no problems.
Offline
On GitHub you see a link to "releases" there you find the 2.2.0 zipped. ref: https://github.com/Proxmark/proxmark3/releases
If you do a "git pull" in your mingw, you get the lastest source since 2.2.0 (which is a bit old) and it should compile just fine.
Offline
Dear iceman & mashmellow,
After changing the rights in ProxSpace directory, it now compiled. Perl still complained about child linked errors but it does compile out.
Thanks.
Offline
@capecode
I have the same issue on my windows 10, 64 bit.
It even gave me several BSOD's.
Installed a new VM with windows 10 and there it compiled successfully.
So it could be some program who is messing up the perlscript for some reason.
About right changes, which permissions did you give?
Offline
I'm always running as a user belonging to the administrator group. I didn't test with a user w limited access. My "proxspace" folder has "full control" set. Since you got BSOD it would be nice to find out what causes it.
Would you mind opening an issue on GitHub?
Offline
The user I use is also in the administrator group and I gave "Everyone" Full control on the Proxspace folder.
So I don't think it's a permission issue.
I will open an issue on Github later this day.
Meanwhile, you told that the mkversion.pl is not mandatory for compiling.
What is the best way to exclude this file for running while compiling?
Looked into every make-file but couldn't find it. Is deleting it sufficient enough?
Thanks!
Offline
Keep to the subject.
Open another thread for your compiling issues.
https://github.com/Proxmark/proxmark3/b … ommon#L105
Last edited by iceman (2016-03-24 15:28:45)
Offline
@Vinnie
I gave the whole folder Admin rights. It compiled with warning but it does produce executable files. I also have Win XP under VMWare. That one didn't give any warnings on Perl.
Offline
@Vinnie
I gave the whole folder Admin rights. It compiled with warning but it does produce executable files. I also have Win XP under VMWare. That one didn't give any warnings on Perl.
Ok
The fix for me was adding /C/ProxSpace/msys/bin to the front of the PATH variable.
Offline
@thankfuluser
I thought it has been done long time ago!!!
here
Offline
Hello all, thanks for accepting a new person into the forum. I wanted to inquire about the standalone functionality for this device per this firmware.
I have a proxmark3 rdv2, LF and HF antennas installed on the device, can use lf commands to search, read and clone just fine on their own (copied a HID prox as a test via those simple commands). However, I noticed that the standalone mode appears to only store and read in HF bands. I ran the proxmark3 console while using the button and standalone mode and it appears to only utilise the HF sensor for bank 0 and bank 1. I have tried isolating the device so only the LF antenna is connected to it and still it only seems to want to work with the HF antenna and cards.
Is this a common problem or am I missing something? Please let me know if further debugging information from my setup is needed. As far as I can tell I am running 2.5.0 via connecting proxmark3 and utilising COM4 in the script. I ran the flash full image batch file successfully.
The following is proxmark3 bootup info for version:
Prox/RFID mark3 RFID instrument
bootrom: /-suspect 2015-11-19 10:08:02
os: /-suspect 2015-11-19 10:08:09
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at 9: 8: 8
uC: AT91SAM7S512 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 512K bytes. Used: 169916 bytes (32%). Free: 354 372 bytes (68%).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory
Thanks all for the help in advance, some excellent talent here!
Offline
Start another thread for this subject, search forum for "standalone mode" to find other threads.
Offline
Hi.
When will be the upgrade of pm3-bin to version 2.6.0.
Could you put the hardnested and do something else. As a suggestion
Thanks
Offline
please you say =================================================================================
Instructions to Update from 0.0.7 (or earlier) to 2.0.0:
1st - FLASH 2.0.0 BOOTROM
2nd - HOLD THE PM3 BUTTON AND FLASH 2.0.0 OS IMAGE (fpga image will be no more needed, it will be all inside osimage from now on!)
but in last pm3-bin-2.5.0 there is no OS image.
why? just need to make fullimage and boot rom since 2.0?
Offline
I'vent seen Asper for a long time now, so my guess there will not be any pm3-bin v260.. And since its based on PM3 there will not be no hardnested either.
The breaking changes made the os image redundant.
In v2.x.x you only need to flash bootrom and fullimage. *Simpler*
Offline
RIP Asper... you are being missed
Offline
Guys
I'm a little stuck here. I can't seem to upgrade my elechouse V2.
I ran two different flashers, the easy flasher and the one included in 2.5 but my unit keeps saying:
C:\zip\pm3-bin-2.5.0\win32 (client+GUI)>proxmark3 com3
Prox/RFID mark3 RFID instrument
bootrom: /-suspect 2015-11-19 10:08:02
os: /-suspect 2015-11-19 10:08:09
LF FPGA image built for 2s30vq100 on 2015/03/06 at 07:38:04
HF FPGA image built for 2s30vq100 on 2015/11/ 2 at 9: 8: 8
uC: AT91SAM7S512 Rev B
Embedded Processor: ARM7TDMI
Nonvolatile Program Memory Size: 512K bytes. Used: 169916 bytes (32%). Free: 354
372 bytes (68%).
Second Nonvolatile Program Memory Size: None
Internal SRAM Size: 64K bytes
Architecture Identifier: AT91SAM7Sxx Series
Nonvolatile Program Memory Type: Embedded Flash Memory
proxmark3>
It's :
bootrom: /-suspect 2015-11-19 10:08:02
os: /-suspect 2015-11-19 10:08:0
So it hasn't upgraded to 2016...
Any clues why?
Offline
Cause the code you are flashing is from 2015.
Offline
oh marsmellow silly me! Thanks and sorry
Just out of curiosity, do all builds come with a new FW/bootrom to flash?
*Newbie trying to learn. I did read the wiki but it's still confusing.
Edit
Edit 2: Yes to above I think i get it.
Last edited by raptor (2016-12-08 22:23:07)
Offline
Hi
someone tested the new version 2.3.0 of RYSCC company creator of the proxmark3 the updated version?
There is something new that you do not have the 2.5.0 of ASPER?
Please I have doubts of whether or not to upgrade my proxmark3.
https /store.ryscc. com/blogs/news/upgrading-your-proxmark3-to-v2-3-over-usb
Offline
Hi, pm3-bin-2.5.0 download link is not working.
Offline
its a quite old version. I suggest you go for github and compile instead.
Offline
I agree with iceman compiling direct from github code is the best way to go.
Until you get your compile environment figured out this link has a bit newer compiled stuff. http://www.proxmark.org/forum/viewtopic.php?id=3975
Offline
ok, thanks!
Offline
Hello everyone, you could help what is the latest version
Proxmark Client By El Gaucho De La Livida Palude Version 1.7 ??
1.7? ( or is there an even newer one? )
2
Can anyone give me the latest compiled version
pm3-bin-2.5.0
Or maybe newer
I would be very grateful for any help in advance thanks a lot.
p/s If this is important, I work with Windows 10 (64bit) and I have proxmark3 Easy.
Offline
did someone try the 9 ( Aideepen ST-Link V2 Programming Unit Mini STM8 STM32 Emulator Downloader M89 )
for flash the proxmark3 rdv401 is ok ?
i need help i tried to flash the proxmark3 rdv from rdv40-64-20201119- to
pm3-bin r763 and after this is not appear to any com port i try it in linux the same the leds A and C are on and they blinks the j-link-v8 is not aviable
i see how you doing with ST-Link V2 ( http://wiki.yobi.be/wiki/Proxmark ) but me i need the to flash this version C:\proxmark3\pm3-bin-756 (cdc+lua)\pm3-bin-756\firmware_win
there it have many images fullimage.elf ,fpgaimage.elf, osimage.elf and in \pm3-bin-756\firmware_win\bootrom folder bootrom.elf
question 1
what is difference of ,fpgaimage.elf, osimage.elf, fullimage.elf i use the fullimage.elf ?for full image and bootrom.elf for boot ?
question 2.
the elf files they supported with telenet only or i can convert to bin?
is more easy for me to use the proxmark3 rdv4 with proxmark tool couse i am beginner to commands than to use the precompile software and drivers like rdv40-64-20201119
Last edited by zissilia (2020-11-24 21:35:12)
Offline
hf search
command doesn't exist
Offline