Proxmark3 community
Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Announcement
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
#1 2008-11-19 23:07:57
- d18c7db
- Contributor
- Registered: 2008-08-19
- Posts: 292
Proxmark3 board build pictures
I finally got around to posting some pictures on flickr of my first board I built last week. Took me about 6 hours of hand soldering everything.
Offline
#2 2009-02-26 09:43:45
- ajoakim
- Member
- Registered: 2009-02-21
- Posts: 4
Re: Proxmark3 board build pictures
Would you be able to post the schismatics for your jtag unit
thank you
Offline
#3 2009-02-26 13:57:19
- n0t
- Contributor
- Registered: 2008-11-24
- Posts: 26
Re: Proxmark3 board build pictures
Would you be able to post the schismatics for your jtag unit
thank you
Read this post:
http://proxmark.org/forum/viewtopic.php?id=149
Offline
#4 2009-02-26 19:00:20
- ajoakim
- Member
- Registered: 2009-02-21
- Posts: 4
Re: Proxmark3 board build pictures
I am using this JTAG , the one in the manual is vague as to what the schematics are, if some one wants to clear it up i would be great full.
Last edited by ajoakim (2009-02-26 19:01:52)
Offline
#5 2009-02-27 15:55:44
- n0t
- Contributor
- Registered: 2008-11-24
- Posts: 26
Re: Proxmark3 board build pictures
Did you try this? It's from the manual.
Pins 3, 4 and 5 are the same.
Offline
#6 2009-03-03 22:21:14
- ajoakim
- Member
- Registered: 2009-02-21
- Posts: 4
Re: Proxmark3 board build pictures
Yeap i tried that it didn't work i guess i fried my Amtel Chip 
, but i didn't solder it for that long one pass with a 14w iron did it. Hummm how can i check to see if the chip is working, with out a scope.
Offline
#7 2009-03-04 02:45:18
- shinechou
- Contributor
- Registered: 2008-10-20
- Posts: 35
Re: Proxmark3 board build pictures
Did you try this? It's from the manual.
Pins 3, 4 and 5 are the same.
http://i39.tinypic.com/2vsniae.jpg
I'd tried it but didn't work too!
Offline
#8 2009-03-04 14:06:05
- n0t
- Contributor
- Registered: 2008-11-24
- Posts: 26
Re: Proxmark3 board build pictures
Try to check your cable make sure you have the correct pins.
Pin 1 referenced below:
Parallel port 3 -> Pin 7 Prox
Parallel port 4 -> Pin 9 Prox
Parallel port 5 -> Pin 5 Prox
Parallel port 11 -> Pin 13 Prox
Parallel port 18-25 -> Pins 4,6,8,10,12,14,16,18,20 Prox
Also try a different computer or try changing the parallel port setting within your BIOS.
I got mine to work in ECP mode even thought the documentation says not to use it.
Hope this helps!
Last edited by n0t (2009-03-04 14:10:22)
Offline
#9 2013-11-01 11:33:10
- asper
- Contributor
- Registered: 2008-08-24
- Posts: 1,409
Re: Proxmark3 board build pictures
Which software to flash form parallel port ?
Offline
#10 2013-11-01 16:18:26
- vivat
- Contributor
- Registered: 2010-10-26
- Posts: 332
Re: Proxmark3 board build pictures
http://proxmark.org/files/Flash/
There is also schematics of wiggler jtag
Offline