Proxmark3 community
Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Announcement
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
Pages: 1
#1 2015-12-05 06:33:34
- honey2pie
- Contributor
- Registered: 2015-12-05
- Posts: 5
How to write block0 data on t5577
I have an v2.5 updated proxmark3 v2 from china.
At frist
I'm trying to read the block 0 data with
lf t55xx read b 0
the proxmark response ::
proxmark3> lf t55xx read b 0
Reading Page 0:
blk | hex data | binary
So I run config command
lf t55xx config b 64
the proxmark response ::
proxmark3> lf t55xx config b 64
Modulation : ASK
Bit Rate : 5 - RF/64
Inverted : No
Offset : 0
Block0 : 0x00000000
After that read again
lf t55xx read b 0
the proxmark response ::
proxmark3> lf t55xx read b 0
Reading Page 0:
blk | hex data | binary
0 | FFB3C002 | 11111111101100111100000000000010
I believe the data I got is wrong
So I do set the offset in the config command. The read output changed
So could you explain the procedure of reading/writing data to the t 5577 ?
thank you
Offline
#2 2015-12-05 11:17:26
- Danz
- Contributor
- From: Dubai
- Registered: 2015-10-24
- Posts: 98
Re: How to write block0 data on t5577
Lf t55 dump
Offline
#3 2015-12-05 11:19:58
- iceman
- Administrator
- Registered: 2013-04-25
- Posts: 9,538
- Website
Re: How to write block0 data on t5577
when dealing with the "lf t55xx" commands... always run "LF T55XX DETECT" first.
Offline
#4 2015-12-05 12:18:29
- honey2pie
- Contributor
- Registered: 2015-12-05
- Posts: 5
Re: How to write block0 data on t5577
this is what I got, after running the command
proxmark3> lf t55xx detect
Could not detect modulation automatically. Try setting it manually with 'lf t55xx config'
Offline
#5 2015-12-09 14:44:19
- honey2pie
- Contributor
- Registered: 2015-12-05
- Posts: 5
Re: How to write block0 data on t5577
anyway I figure out myself.
the firmware 2.5 doesn't work.
after changing to 2.4 things work fine.
Offline
#6 2015-12-09 14:50:07
- iceman
- Administrator
- Registered: 2013-04-25
- Posts: 9,538
- Website
Re: How to write block0 data on t5577
did you download the latest source from github, or did you take @asper's precompiled distro? The v2.5. from @asper is one month old, that may have been fixed in the source on github.
Can you compile and flash the latest on github and test?
Offline
#7 2015-12-09 15:56:00
- honey2pie
- Contributor
- Registered: 2015-12-05
- Posts: 5
Re: How to write block0 data on t5577
Since, I dont konw how to compile the firmware, I use the one from
http://www.proxmark.org/forum/viewtopic.php?id=1562
Offline
#8 2015-12-09 16:04:06
- iceman
- Administrator
- Registered: 2013-04-25
- Posts: 9,538
- Website
Re: How to write block0 data on t5577
ok, that would explain things.
Offline
Pages: 1