Proxmark3 community
Research, development and trades concerning the powerful Proxmark3 device.
Remember; sharing is caring. Bring something back to the community.
"Learn the tools of the trade the hard way." +Fravia
You are not logged in.
Announcement
Time changes and with it the technology
Proxmark3 @ discord
Users of this forum, please be aware that information stored on this site is not private.
Pages: 1
#1 2014-12-17 18:49:51
- Omikron
- Contributor
- Registered: 2010-02-12
- Posts: 78
Proxmark Client Hanging CONSTANTLY
Hey Guys!
Does anyone know why the PM3 client would hang constantly during use? I am running the latest git version throughout the last 10 revisions or so and it's either stayed the same or gotten worse, but it's INCREDIBLY frustrating.
Often times commands issued will be delayed for many many seconds (even simple ones like hw version) and will just fail completely other times. The only time that appears to be "reliable" for command execution is right after starting the client. It works very consistently, but then deteriorates to a crap-pile just a few commands later. Exiting (or CTRL-C'ing) out of the client and restarting it resolves the issue every time, even though the PM3 does not have to be power cycled. This tells me that it's an issue with the client.
Any thoughts? Has anyone else observed similar frustrations?
Offline
#2 2014-12-17 19:11:22
- iceman
- Administrator
- Registered: 2013-04-25
- Posts: 9,538
- Website
Re: Proxmark Client Hanging CONSTANTLY
Been running latest revision for several months, and I don't experience the same. Since there has been changes in the fpga-code don't forget to flash the bootrom, and fullimage ...
Offline
#3 2014-12-17 23:15:28
- Omikron
- Contributor
- Registered: 2010-02-12
- Posts: 78
Re: Proxmark Client Hanging CONSTANTLY
Been running latest revision for several months, and I don't experience the same. Since there has been changes in the fpga-code don't forget to flash the bootrom, and fullimage ...
Yep, fully aware of all that, and I always update both when in doubt. :-)
What OS are you on?
If it's relevant, I'm compiling on OS X 10.10.1.
Offline
#4 2014-12-17 23:22:19
- iceman
- Administrator
- Registered: 2013-04-25
- Posts: 9,538
- Website
Re: Proxmark Client Hanging CONSTANTLY
ubuntu.
I think I saw someting on the forum about osx and problems...
Offline
#5 2014-12-18 09:07:55
- holiman
- Contributor
- Registered: 2013-05-03
- Posts: 566
Re: Proxmark Client Hanging CONSTANTLY
I don't have those kind of problems; however, sometimes when I do flash, client, flash, client etc (the dev-cycle), I get a USB-crash on the host. It basically kills the entire USB-stack, so even my USB mouse stops working. My laptop is using usb3, xhci. On older ubuntu, sometimes the computer would completely unrecoverably freeze when using usb3 on linux, so I'd always use usb2 (ehci) instead. The xhci is a bit unstable. Even though my problem seems totally unrelated to yours, you could try using only usb2 if possible.
Edited: wrote "usb3 (ehci)", but meant "usb2(ehci)".
Last edited by holiman (2014-12-19 09:01:07)
Offline
#6 2014-12-18 23:29:01
- Omikron
- Contributor
- Registered: 2010-02-12
- Posts: 78
Re: Proxmark Client Hanging CONSTANTLY
I don't have those kind of problems; however, sometimes when I do flash, client, flash, client etc (the dev-cycle), I get a USB-crash on the host. It basically kills the entire USB-stack, so even my USB mouse stops working. My laptop is using usb3, xhci. On older ubuntu, sometimes the computer would completely unrecoverably freeze when using usb3 on linux, so I'd always use usb3 (ehci) instead. The xhci is a bit unstable. Even though my problem seems totally unrelated to yours, you could try using only usb2 if possible.
Very interesting note about forcing USB2 drivers. I'll see if there is anyway to do that on OS X.
Offline
Pages: 1